BASEMENT LIGHT SWITCH TEENAGENT HOW TO
BASEMENT LIGHT SWITCH TEENAGENT INSTALL
BASEMENT LIGHT SWITCH TEENAGENT CODE

BASEMENT LIGHT SWITCH TEENAGENT INSTALL

These boxes are easy to install and can be gotten from Amazon or your local Hardware store. Yes, there are special switches you can get, or you can use a regular indoor switch and mount it inside a special weather resistant switch box. What if you want a light switch outside? Maybe to control your bistro lights or some other fixture? This is actually possible, and done all the time.

BASEMENT LIGHT SWITCH TEENAGENT CODE

I understand why halls and stairs need lights and switches – it’s for safety, but why don’t you need to have a switch in the room? Doesn’t really make sense to me, but apparently that’s the way the code is written. You could mount a switch for the bedroom outside the door, or even on the other side of the house if you want. Strangely enough, unless the room is a stairway, hallway, or a few other select places, the light switch doesn’t even have to be inside the room. I just flip the switch and presto! The attic is illuminated.Īt the same time, I also never forget to turn the light off when I leave the attic because I can just look up and see if the switch is on or off. It is really quite handy, because whenever I go into the attic to change my air filters, I don’t have to bring a flashlight or struggle to find the pull cord for some old fashioned light bulb.

It’s in the upstairs game room, and it is put next to the attic pull down ladder. I actually have a wired light switch on the ceiling in my house. Can you put a light switch on the ceiling? In addition to the usual place near a door where you might find a light switch, here are a few more unusual locations that are allowed. Light switches at different heights Other places for light switches. It’s not really that common for private residences. Did you know that ADA is for PUBLIC spaces? You don’t need to follow ADA rules in your house unless you have special local requirements. One thing to note is about ADA compliance. This is to allow for people in wheelchairs or other alternative needs to be able to turn on and off the switches. Most local building code requirements allow for switches to be as low as 15 inches from the floor. Thankfully the electrician who wired my house was a rule follower! How low can I put a light switch? It’s sort of strange or weird if you put your hand out and it’s not where it is expected to be.Īs a general guideline whenever I am installing a new switch in my house, or relocating one because of a remodel or renovation job, I like to put it at exactly the same height as the rest of the switches in my house which is exactly 48″. Have you ever walked into a dark room and reached for the light switch? It’s usually in the same place, or at least pretty close to it. What is the standard height for a light switch from the floor? Light Switch Code Requirements It’s high enough that little kids won’t play with it, at least not too much, and folks in wheelchairs can reach it easily too.

This is just about the perfect measurement for most people. The official height is 48 inches from the floor, however it is common practice to mount it between 42″ – 48″ according to local building codes. The NEC is the benchmark for all 50 states for safe electrical design.Ī light switch (or other approved wall mounted control device) must be mounted near the entrance to the room. Just reading other posts and noticed some people were asked to clarify.The official guide to light switch Location Code requirements can be found in the National Electric Code (NEC) sec 210.70. Quick edit- this is in the US if that helps at all.

BASEMENT LIGHT SWITCH TEENAGENT HOW TO

TLDR: how to separate power from lights and outlets one one circuit and one switch. I am a diy here so if I need to call in the big guns what am I looking at to get this cleaned up? If this is something that could be tackled any suggestions on where to start would be amazing. (Lights on - outlet power// lights off no power) There is one outlet that is the exception to this right next to my utility room which I’m guessing was already there before this room was finished and whatever this guy did to wire up the finished basement had to have been amateur/diy? This doesn’t seem like it would be to code for the simple reason I’ve been searching for this online for hours with nothing remotely close but fortunately found this subreddit. (Lesson learned) There are about 8 outlets in this room and they are all on the same on/off circuitry as the lights. The main area has a quirk that was completely missed due to the room being empty and only flicked the lights on and off during showing/inspection. Hi - so I just bought a house with a newly finished basement.

Basement light switch teenagent